samsung dryer model dve50r5200w manual

The Samsung DVE50R5200W is a 7.4 cu. ft. electric dryer featuring Sensor Dry technology, Wrinkle Prevent option, Steam Refresh cycle, multiple dry cycles (Normal, Heavy Duty, Delicates, etc.), adjustable temperature settings, end-of-cycle signal, and a reversible door. It requires a 240V electrical outlet. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

Features at a Glance

Key components: Control Panel, Drum, Lint Filter, Venting connection, Power Cord, Reversible Door, Sensor Dry system.

Installation

Unpack and inspect contents. Ensure location is level and near proper electrical outlet and venting.

1. Remove shipping materials: Remove all tape, brackets, and foam from drum interior and exterior.
2. Level the dryer: Adjust leveling feet so dryer is stable and does not rock.
3. Connect venting: Use rigid metal or flexible metal duct (do not use plastic). Keep vent run as short and straight as possible.
4. Electrical connection: Plug into dedicated 240V, 30-amp outlet. Ensure power is off during connection.
5. Test installation: Run a short air fluff cycle to ensure proper operation.

WARNING! Dryer is heavy; use two people to move. Ensure venting is properly installed to prevent fire hazard.

First-Time Setup

After installation, configure initial settings.

1. Select language: Press and hold Control Lock and Temp buttons for 3 seconds to cycle languages (if applicable).
2. Set end-of-cycle signal: Use Signal button to turn alert On or Off.
3. Configure Wrinkle Prevent: Press Wrinkle Prevent button to set duration (Off, 1 hour, 3 hours, 6 hours).
4. Test Sensor Dry: Load a medium-sized load and run Normal cycle with Sensor Dry to ensure proper moisture sensing.

CAUTION! Do not install in damp or wet locations. Maintain clearances as specified in manual.

Specifications

• Model: DVE50R5200W
• Type: Electric Dryer
• Capacity: 7.4 cubic feet
• Power Requirements: 240V AC, 60Hz, 30-amp circuit
• Dryer Technology: Sensor Dry, Steam Refresh
• Control Type: Electronic with LED display
• Cycles: Normal, Heavy Duty, Delicates, Quick Dry, Air Fluff, Timed Dry, Steam Refresh, Wrinkle Prevent
• Dimensions (HxWxD): Approximately 44" x 27" x 30"
• Weight: Approximately 130 lbs
• Venting: 4-inch diameter exhaust

Controls and Settings

Control Panel: POWER, CYCLE SELECTOR knob, TEMP, TIME DRY, WRINKLE PREVENT, SIGNAL, STEAM REFRESH, START/PAUSE, CONTROL LOCK.

Cycle Guide: Normal (mixed loads), Heavy Duty (towels, jeans), Delicates (gentle heat), Quick Dry (small loads), Timed Dry (manual time), Air Fluff (no heat), Steam Refresh.

Temperature Settings: High (Heavy Duty), Medium (Normal), Low (Delicates), No Heat (Air Fluff). Options: Wrinkle Prevent (Off/1hr/3hr/6hr), End Signal (On/Off), Control Lock (press 3 sec to enable/disable).

Connecting Venting

Proper venting is critical for performance and safety.

1. Use correct duct: Rigid metal duct is recommended. Flexible metal duct is acceptable if not crushed.
2. Route venting: Keep duct straight and short (max length per local codes, typically under 25 feet). Avoid sharp bends.
3. Secure connections: Use metal foil tape (not duct tape) to seal joints. Ensure exterior vent hood opens freely.
4. Check airflow: After installation, run dryer and check for strong exhaust flow at vent outlet.

Tip: Clean lint filter before every load and inspect venting annually for lint buildup.

Using Dryer Cycles

For best results, sort laundry by fabric type and drying needs.

1. Load laundry: Do not overload. Leave space for tumbling.
2. Select cycle: Turn CYCLE SELECTOR to desired cycle (e.g., Normal).
3. Adjust settings: Press TEMP to select heat level. Use TIME DRY for manual time if desired.
4. Add options: Press WRINKLE PREVENT or STEAM REFRESH if needed.
5. Start: Press START/PAUSE. Display shows estimated time remaining.
6. Unload promptly: Remove clothes when cycle ends to minimize wrinkles.
7. Clean lint filter: Remove lint after every cycle.

WARNING! Do not dry items that have been in contact with flammable substances. Do not block vent.

Special Features

Sensor Dry: Automatically stops when desired dryness is detected. Steam Refresh: Adds steam during a cycle to reduce odors and wrinkles on 1-3 items (run empty for 30 minutes first to clean drum). Wrinkle Prevent: Continues tumbling without heat after cycle ends for set period. Control Lock: Prevents accidental button presses (hold for 3 seconds).

Care & Cleaning

Unplug or disconnect power before cleaning. Wipe exterior with damp cloth. Clean lint filter after every load. Monthly: Vacuum lint filter area and check venting for obstructions. Periodically: Wipe drum interior with damp cloth to remove residue.

CAUTION! Do not use abrasive cleaners or solvents. Do not spray water on controls.

Regulatory Information

UL listed. Complies with U.S. Federal energy standards. Manufactured for Samsung Electronics America, Inc. For support, visit www.samsung.com/us/support or contact 1-800-SAMSUNG (1-800-726-7864).

Troubleshooting

Reset: Unplug dryer for 1 minute to reset electronic controls.

Service: 1-800-SAMSUNG; www.samsung.com/us/support