Samsung Dryer DVE52A5500W Manual

The Samsung DVE52A5500W is an electric dryer with a 7.5 cu. ft. capacity, featuring Sensor Dry technology, Steam Sanitize+ cycle, Wrinkle Prevent option, EcoBubble™ for reduced energy consumption, multiple drying cycles, and a reversible door. It requires a 240V electrical connection. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Connecting to Power 7. Using Drying Cycles 8. Special Features 9. Care & Cleaning 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: Large capacity drum, Control Panel, Lint Filter, Reversible Door, Venting system, Power Cord.

FeatureDescription
Sensor Dry TechnologyAutomatically detects moisture levels for optimal drying
Steam Sanitize+Reduces allergens and wrinkles using steam
Wrinkle Prevent OptionTumbles clothes periodically after cycle to reduce wrinkles
EcoBubble™Energy-efficient drying technology
Multiple Drying CyclesCotton, Permanent Press, Delicates, Quick Dry, etc.
Reversible DoorCan be hinged on left or right side
Control LockPrevents accidental changes to settings
End of Cycle SignalAudible alert when drying is complete
Lint Filter IndicatorReminder to clean the lint filter
Digital DisplayShows cycle time, settings, and status

Installation

Unpack and inspect contents. Place on a level, stable floor near a venting outlet and power source.

  1. Remove shipping materials: Take off all tape, bolts, and brackets from drum and interior.
  2. Level the dryer: Adjust leveling feet to ensure dryer is stable and does not rock.
  3. Connect venting: Attach a 4-inch diameter rigid metal duct to the dryer exhaust outlet and vent to outdoors.
  4. Electrical connection: Have a qualified electrician connect to a dedicated 240V, 30-amp circuit.
  5. Test operation: Plug in, run a test cycle to ensure proper installation.

WARNING! Dryer is heavy; use two people for moving. Ensure proper venting to prevent fire hazard.

First-Time Setup

After installation, configure initial settings.

  1. Select language: Press and hold Control Lock for 3 seconds, then choose language on display.
  2. Set time: Use the Time button to set current time.
  3. Choose default cycle: Select preferred cycle (e.g., Cotton Normal) as your default.
  4. Enable features: Activate Wrinkle Prevent or End Signal as desired via Settings menu.

CAUTION! Ensure dryer is properly leveled to prevent vibration and noise.

Specifications

Controls and Settings

Control Panel: POWER, Cycle Selector, Temperature, Dryness Level, Options (Wrinkle Prevent, Control Lock, Signal), Start/Pause.

Cycles: Cotton, Permanent Press, Delicates, Quick Dry, Bedding, Air Fluff, Sanitize, Steam Refresh. Settings: Temperature (High, Medium, Low, No Heat), Dryness Level (More Dry, Less Dry), Time Dry (10-180 minutes). Options: Wrinkle Prevent (tumbles periodically), Control Lock (locks controls), End Signal (audible alert).

Connecting to Power

Must be connected to a dedicated 240V, 30-amp circuit by a qualified electrician.

  1. Turn off power at circuit breaker before installation.
  2. Use a 4-wire power cord (not included) rated for dryer use.
  3. Connect wires to terminal block: Black & Red (hot), White (neutral), Green (ground).
  4. Secure strain relief and plug into outlet. Restore power.

Tip: Ensure venting is clear and lint filter is clean before first use.

Using Drying Cycles

Supports various fabrics and drying needs.

  1. Load dryer: Place clothes loosely in drum; do not overload.
  2. Select cycle: Turn Cycle Selector to desired cycle (e.g., Cotton).
  3. Adjust settings: Choose Temperature and Dryness Level as needed.
  4. Add options: Press Wrinkle Prevent or other option buttons.
  5. Start: Press Start/Pause to begin drying.
  6. Pause/Stop: Press Start/Pause to pause; press again to resume. To cancel, hold for 3 seconds.
  7. After cycle: Remove clothes promptly to reduce wrinkles.

WARNING! Do not dry items containing foam, rubber, or plastic. Clean lint filter before every load.

Special Features

Steam Sanitize+: Reduces allergens and wrinkles. Wrinkle Prevent: Tumbles clothes periodically after cycle ends. Control Lock: Prevents accidental changes. EcoBubble™: Uses less energy for certain cycles.

Care & Cleaning

Unplug before cleaning. Clean lint filter after every load. Wipe exterior with damp cloth; do not use abrasive cleaners. Check and clean venting system annually.

CAUTION! Do not use solvents or spray cleaners on controls. Keep area around dryer free of lint and dust.

Regulatory Information

UL listed; complies with U.S. safety standards. ENERGY STAR® certified. Copyright © Samsung Electronics. For support, visit www.samsung.com/us/support or contact 1-800-SAMSUNG (1-800-726-7864).

Troubleshooting

SymptomPossible CauseCorrective Action
Dryer won't startPower, door, settingsEnsure plugged in, door closed, circuit breaker on; press Start firmly.
Clothes not dryingLint filter, venting, settingsClean lint filter; check vent for blockage; select correct cycle/temperature.
Dryer is noisyObjects in drum, levelingCheck for coins/objects; ensure dryer is level on floor.
Error code on displayVarious faultsRefer to error code chart in manual; common codes: tE (temperature error), dE (door open).
Steam function not workingWater supply, cycleEnsure water is connected; select a steam cycle (Sanitize, Refresh).

Reset: Unplug for 1 minute, then plug back in to reset control board.

Service: 1-800-SAMSUNG; www.samsung.com/us/support

Samsung Dryer DVE52A5500W Manual © - All Rights Reserved 2025